Published July 13, 2026 at 00:48
A hydraulic cylinder housing has an 8 mm-deep retaining ring groove at the Ø 120 mm point on the inside. Diameter requirement: 122.0 ± 0.1 mm. Measuring this diameter is demanding — the groove sits DEEP INSIDE the housing, in a narrow 8 mm-wide cylindrical recess.
A standard digital caliper has small internal knife-edges at the top of the jaws for internal measurement, but they only project ~15-20 mm from the main body. On a 500 mm-long cylinder housing, they don’t reach the 250 mm depth where the groove sits.
A Holtest 3-point micrometer would work — but only for the BORE diameter itself, not the groove’s DIAMETER (which is LARGER than the bore diameter at the point where the groove sits).
The solution: calipers with OUTWARD-FACING MEASURING PINS. The jaws terminate in two cylindrical pins that project OUTWARD from the ends of the jaws. The pins can be inserted into the groove from BOTH SIDES to measure the diameter.
Two types of ”internal measurement”
The term ”internal measurement” is actually ambiguous and needs clarifying:
Bore diameter (Type 1): The diameter of A CYLINDRICAL BORE with straight walls. Standard measuring tools: Holtest 3-point micrometer (I wrote about this for m-dk previously), 2-point bore mike, or internal knife-edges on calipers.
Groove diameter (Type 2): The diameter of a RECESS in the bore wall. Diameter LARGER than the bore diameter. Standard tool: CALIPERS WITH OUTWARD-FACING MEASURING PINS — like this Schut model.
The difference is fundamental and requires different instruments. A Holtest can measure bore diameter but not groove diameter (its force-transmission mechanism doesn’t work across ”step-outs” in the wall).
Rounded measuring pins — a geometric choice
Outward-facing measuring pins are typically ROUNDED (cylindrical) with a diameter of ~2-4 mm. Why not pointed or flat?
Cylindrical rounded: Provides LINE CONTACT against the groove’s side walls. Reproducible contact point. Standard for this type of measurement.
Pointed: Would give POINT contact. Creates very localized force concentration that could damage the groove’s edge over time.
Flat: Wouldn’t fit into narrow grooves. Only suitable for larger openings.
This Schut model typically has Ø 3-4 mm rounded pins — fits into grooves from 5 mm width and up.
Measuring range 60-500 mm
The caliper’s measuring range starts AT 60 mm — not at zero. Reason: the pins’ geometry REQUIRES a minimum opening size for the pins themselves to fit.
- At the zero position: the pins almost touch each other. No measuring capacity.
- At a 60 mm opening: the pins project away from each other. Can measure grooves with a diameter of 60-500 mm.
- At a 500 mm opening: the caliper’s maximum reach.
For smaller grooves (under 60 mm), other instruments are needed — internal micrometers with a specific geometry for a smaller range.
Absolute encoder
This instrument has an ABSOLUTE encoder (I wrote about this technology in a previous article about spline micrometers). Advantages:
- No re-zeroing needed at startup.
- No data loss when changing the battery.
- Reads the current position instantly at any time.
During a batch measurement session, the operator can change the battery mid-session without losing the zero reference. Critical for production QC.
Workflow
- Open the caliper so the pins are wider than the groove diameter.
- Insert the jaws THROUGH the bore opening until the pins are level with the GROOVE.
- Close the jaws slowly until BOTH PINS touch the groove’s opposing inner walls.
- Read the digital display: the groove’s diameter.
- Remove the instrument carefully — the pins must not scrape against the groove’s edge on withdrawal.
Total time per measurement: 15-30 seconds. Faster than many alternative methods.
Applications
Hydraulic cylinder QC: Retaining ring grooves, sealing surface grooves.
Engine and transmission maintenance: Piston ring grooves, keyways, snap-ring grooves.
Pump housing measurement: Bearing grooves, seal seat diameter.
Pipe and fitting inspection: Flange grooves, seals.
Toolmaker work: When manufacturing custom components with grooves.
Refurbishment workshops: For wear measurement on old components.
What you get for your money
Schut digital caliper with outward-facing measuring pins for internal diameter and groove measurements, measuring range 60-500 mm, resolution 0.01 mm, absolute encoder (no zero loss on battery change), hardened ground stainless steel measuring pins, matte-chrome reading surface, mm/inch switching, on/off, zero-set, CR2032 battery, ECONOMY LINE build quality. SEK 5,065.
A specialized tool for workshops that regularly measure groove diameters in bores — hydraulic cylinders, engine housings, transmissions. Complements the Holtest 3-point micrometer (for bore diameter) and calipers with internal knife-edges (for open internal measurement). Standard equipment in engine and hydraulics workshops.
Read more: Digital caliper with outward-facing measuring pins in the shop →