Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The bearing sounded fine on Thursday and failed on Monday: how logged vibration values make wear visibleGhost voltage that disappears when the meter loads the circuit: how to tell real voltage from falseThree seconds and the right viewing angle: how temperature checks actually get doneWhy a Vernier Caliper Shows a Different Depth Every Time and What a Depth Micrometer Does DifferentlyA bore can hold size at one point and still be both tapered and ovalThe temperature was right when the load was loaded, but what happened during transport?With a 0.4-second temperature reading, you can measure accurately before the product has had time to changeCore temperature is what counts: how to document cooling and heating processes without handwritten listsThe cold chain failed overnight, but nobody can prove when or for how longUsing the Same Thermometer for Raw and Cooked Meat Is a Risk That Two Colors RemoveVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The bearing sounded fine on Thursday and failed on Monday: how logged vibration values make wear visibleGhost voltage that disappears when the meter loads the circuit: how to tell real voltage from falseThree seconds and the right viewing angle: how temperature checks actually get doneWhy a Vernier Caliper Shows a Different Depth Every Time and What a Depth Micrometer Does DifferentlyA bore can hold size at one point and still be both tapered and ovalThe temperature was right when the load was loaded, but what happened during transport?With a 0.4-second temperature reading, you can measure accurately before the product has had time to changeCore temperature is what counts: how to document cooling and heating processes without handwritten listsThe cold chain failed overnight, but nobody can prove when or for how longUsing the Same Thermometer for Raw and Cooked Meat Is a Risk That Two Colors Remove

Sine Vise 0–45° — the Angle Is Never Better Than What Holds the Workpiece

Published August 20, 2026 at 07:13

The drawing calls for 30°, tolerance ±10 arc minutes. You clamp the part in an ordinary vice, lean it against an angle plate, tighten — and feel it shift that last bit as the jaw grips. Then you mill. The measurement afterward reads 30°12′. No one did anything wrong on the machine; the error occurred before the chip was taken, in whatever held the workpiece. A machined angle can never be more accurate than the setup it was made in.

High-precision sine vice with rotatable base, adjustable 0–45°, jaw opening 120 mm

What it is

A hardened sine vice with a rotatable base, providing stable and accurate clamping at any angle setting between 0 and 45°. The jaw opening is 120 mm, jaw width 100 mm, and jaw depth 45 mm; the overall unit is 250 mm long. The reference surfaces are hardened and ground.

The problem it solves

The name comes from the sine principle: instead of reading off a degree scale, the angle is set using a known height dimension over a known distance, and trigonometry gives the angle. It’s the same principle as in a sine bar, and the point is that it translates an angle problem into a length problem — and length we can measure with gauge blocks and dial indicators down to the micrometer level, while a degree scale marked in 1° increments never comes close. The angle thus becomes as accurate as the length measurements it was built from.

The second problem is stability. A workpiece resting in an improvised setup — wedges, parallel supports, an angle plate and a feel for it — may sit correctly the instant you check it and still move when the jaw is tightened or when the mill takes hold. A design built to lock in the angle position absorbs the cutting forces instead of yielding to them, and that’s the difference between hitting the angle once and hitting it on part number forty as well.

The third benefit is repeatability. A setting based on a documented height dimension can be reproduced exactly six months from now when the same part is ordered again — the rig doesn’t need to be reinvented, and the next operator gets the same result as the last one. A setup that exists only in someone’s hands disappears the day that person is out sick.

Three typical use cases

  • Toolmaking and grinding: chamfer angles, cutting geometries, and guide surfaces where the tolerance is specified in arc minutes rather than whole degrees.
  • Milling angled surfaces: slots, chamfers, and mating surfaces that must sit at a precise angle to a reference surface — clamp once, machine to completion.
  • Metrology labs and inspection: holding a part at a known angle during measurement, so you measure the deviation from the angle rather than the sum of the deviation and a sloppy setup.

Why it pays off

The cost lies in setup time. Fiddling together an angled clamping setup with wedges and supports, measuring, adjusting, measuring again and still being unsure takes minutes — often tens of minutes — per part, and they recur every time the job comes up. A fixed design that’s set once and locked removes both the fiddling and the uncertainty.

Then there’s scrap, which is the expensive item. An angle deviation is rarely caught at the machine; it’s caught during inspection or assembly, when the part already carries the added value of several operations. And unlike a dimensional error, a misangled cut usually can’t be salvaged with a rework. A vice that gets the angle right from the start pays for itself in the parts that never had to be scrapped — and in the reruns that never had to be scheduled on the machine.

Read more about the 0–45° sine vice, 120 mm jaw opening →

More news

All news